Denali
Denali
Sort by
Show result
  • 113 Decibels at 3 feet
  • Operating voltage:12 Volts (11.7volts required)
  • Power draw: 5 Amps
  • Single piece design
  • Dimensions: Approximately 3.25" x 3.4" x 2.5"
  • Stylish all black design
  • Fits in most factory horn locations
RM185.00
  • 120 Decibels at 3 feet
  • Operating Voltage: 12V
  • Power Draw: 20 amps
  • Size (Compressor): 4.5" x 2.9" x 3.0"
  • Size (Acoustic Unit): 4.1" x 3.7" x 3.4"
  • Housing: Two Part Design
  • CANbus Compatible
RM375.00
  • High/Low Sync - Set auxiliary lights to switch between a programmable high/low setting with the factory high beam switch.
  • ON/OFF and Dim - Independently control two sets of lights ON/OFF and change intensity level (for both day and night) right from your original vehicle switches.
  • Modulate Lights - Set auxiliary lights to modulate to increase your visibility to other motorists.
  • Flash to Pass - Need to get someone's attention? Pulse your high beam switch three times and your auxiliary lights will strobe three times fast.
  • Cancel With Turn Signal - This feature cancels the corresponding auxiliary light when you turn your turn signal on preventing powerful auxiliary lights from overpowering your signal.
  • Inverse Flashing With Hazards - This features flashes your auxiliary lights inversely to your hazard lights, increasing visibility during road side emergency's. 
  • Plug & Play Horn Installation - Quickly and easily connect high power aftermarket horns like our SoundBomb™ without having to add an additional harness or relay.
  • Strobe with Horn - With this feature selected the CANsmart™ software will automatically strobe your auxiliary lights when you sound your horn. This feature works whether you have the factory horn or SoundBomb™ horn installed.
  • Deceleration Activated "Smart Brake" Technology - The CANsmart™ reads vehicle speed in real time to activate your brake light during deceleration before you even touch the brake. You can adjust the sensitivity and minimum speed at which the Smart Brake Feature will activate.
  • Flash Pattern Braking - The CANsmart™ provides four different flash patterns that make our super bright auxiliary brake lights even noticeable to motorists behind you. You can set auxiliary brake lights to only flash under hard braking, flash continuously as your brake is applied or flash four times rapidly then hold steady (California legal flash rate).
  • Circuit Function Selector - The Circuit Function Selector in the CANsmart software will let you run any accessory of your choice on any of the four circuits. Click on a circuit icon to open the drop down menu and make your selection from the list of available circuit functions.
  • Switched Power Source - The CANsmart™ provides a universal "accessory" option which simply gives you clean switched 12V power. That means whatever accessory you connect to this circuit will turn on and off with your ignition.
  • Delay Time Out - You can also set the accessories on this circuit to have a delayed time out. This will keep them powered for up to 30 seconds after your turn off your bike.
  • On Board Power - The "accessory" circuit option is ideal for powering your GPS, phone, heated gear or any other electronic device.
RM1,460.00
  • LED’s: (2x) 10 Watt Cree XPL HI
  • Power Draw: 1.6 Amps
  • Beam Distance (Spot): 525 Feet
  • Beam Width (Spot): 75 Feet
  • Raw Lumens: 2190
  • Intensity: Single Intensity Harness
  • DataDim™ Compatible: Yes
  • Operating Voltage: 12 VDC
  • Pod Size: 2.2” Round x 2.4” Deep (each)
  • Pod Weight: 0.6 lbs (each)
  • IP67 Waterproof & Submersible
  • E Mark Approved Flood Lenses
RM1,650.00
  • LED’s: (8x) 10 Watt Cree XPL HI 
  • Power Draw: 6.6 Amps 
  • Beam Distance (Spot): 800 Feet 
  • Beam Width (Spot): 110 Feet 
  • Raw Lumens: 8760 
  • Intensity: Single Intensity Harness 
  • DataDim™ Compatible: Yes 
  • Operating Voltage: 12 VDC 
  • Pod Size: 3.9” Square x 2.6” Deep (each)
  • Pod Weight: 1.55 lbs (each)
  • IP67 Waterproof & Submersible 
  • E Mark Approved Spot Lenses 
RM1,898.00
  • Sound Output: 120 dB at 3 feet 
  • Current Draw: 20 Amp 
  • Dimensions: 5.4” (137mm) wide x 4.5” (116mm) high x 3.6” (86 mm) deep 
  • Stylish All Black Design
  • CANbus compatible
RM375.00
  • Enables true plug & play connection 
  • Plugs directly into OEM BMW horn connector
  • No need to modify factory wiring
  • No other wiring needed for SoundBomb Mini
  • Functions as trigger for SoundBomb Horn Wiring Harness
  • Simple & easy to install
RM120.00